There is no substitute for an OLT to make a good and secure network. When a large network is serviced by breaking it down into smaller segments, the lowest cost you can network is through an OLT. So guys today I will talk about some SHOW commands of BDCOM OLT. These commands are always useful. Many people have OLT, but they don't know how to work in OLT. Today's article is for them. Hope you all can work on your own OLT from now on. Along with that many SHOW commands are given below.
Many times it is seen, many people forget all the commands even after memorizing them. So if you have notes, you will remember the command in just a glance. Below are many show commands of BDCOM OLT, follow them. Hope you will benefit a lot.
All Show Commands:
* show running-config - Using this command to show OLT full configuration.
* show running-config interface epON 0/1 - Use this command to show specific epon interface configuration.
* show running-config interface epON 0/1:1 - Using this command to show specific epon onu configuration.
* show running-config interface gigaEthernet 0/1 - Using this command to show specific gigaEthernet interface configuration.
* show epon active-onu - Using this command to show all active onu information.
* show epon active-onu interface epON 0/2 - Using this command to show specific active onu information.
* show epon active-onu mac-address b485.3d26.d8d3 - Using this command for searching onu by mac address.
* show epon always-laser-on-onu - Use this command to check the always laser status on the onu.
* show epon always-laser-on-onu interface epON 0/2 - Using this command for specific epon always laser status on the ONU.
* show epon basic-info - Using this command for basic information of the OLT.
* show epon encryption - Use this command to show the global-level encryption parameters of an OLT.
* show epon encryption interface epON 0/2 - Use this command to show specific epon interface global-level encryption parameters of an OLT.
* show epon inactive-onu - Using this command to show inactive ONU information.
* show epon inactive-onu interface epON 0/2 - Using this command to show specific epon interface inactive ONU information.
* show epon interface epON 0/2:2 onu ctc basic-info - Using this command to find out onu mac address.
* show epon interface epon 0/2:2 onu port 1 state - Using this command for onu lan port status check like UP or Down.
* show epon interface epon 0/3:2 onu ctc dba - Using this command to show the onu queue the DBA set the config.
* show aaa users - Use this command to show AAA active Login user configuration.
* show aggregator-group detail - Use this command to show link aggregation(LACP or Bonding) information.
* show alias - Use this command to show the alias command.
* show the arp - Use this command to show an arp table with IP and interface.
* show break - Use this command to show switch breakpoint information.
* show cpu - Use this command to show how much CPU usage is in OLT.
* show debug - Use this command to show the state of each debugging option.
* show dot1x - Using this command for show IEEE 802.1X information.
* show epon optical-transceiver-diagnosis - Use this command to show all epon optical power (dBm).
* show epon optical-transceiver-diagnosis interface epON 0/2 - Using this command for show specific epon all onu optical power(dBm).
* show epon optical-transceiver-diagnosis interface epON 0/2:1 - Using this command for show specific ONU Optical power(dBm).
* show gpon optical-transceiver-diagnosis interface gpON 0/2 - Using this command to show all onu rx tx power only for GPON OLT.
* show epon interface epON 0/2:2 onu ctc SNMP-info - Using this command to show ONU SNMP information.
* show epon interface epON 0/2:3 onu d-info - Using this command to show double mac address information.
* show epon interface epON 0/2:5 onu mac address-table - Using this command to show onu mac address table.
* show epon interface epON 0/2:4 onu mac-aging-time - Using this command to show onu MAC aging time.
* show epon interface epON 0/2:9 onu pon-port statistics - Using this command to show ONU interface statistics.
* show epon interface epON 0/2:10 onu pon-port state - Using this command to show ONU interface state.
* show epon interface epON 0/2:12 onu port 1 ctc auto-negotiation - Using this command to show onu interface auto-negotiation.
* show epon interface epON 0/2:14 onu port 1 ctc flow-control - Using this command to show onu interface flow control state.
* show epon interface epON 0/2:14 onu port 1-4 mcst mc-VLAN - Using this command to show onu multicast.
* show epon interface epON 0/2:14 onu port 1 ctc mcst tag-stripe - Using this command to show onu strive VLAN tag.
* show epon interface epON 0/2:14 onu port 1 ctc QoS - Using this command to show onu interface qos.
* show epon onu-information - Use this command to show all onu information under every epon.
* show interface brief - Use this command to show all interface statuses.
* show interface range epON 0/1 - Using this command for show epon tx & rx power(dBm) & all status.
* show interface epON 0/2 - Use this command to show specific interface information.
* show ip route detail - Use this command to show all routes in olt.
* show ip route-static - Using this command to show the static route.
* show ip interface vLAN 1 - Use this command to show specific interface IP configuration.
* show local users - Use this command to show all users.
* show logging - Use this command to show all logs.
* show mac address-table - Use this command to show all mac address tables.
* show mac address-table interface epON 0/1 - Using this command to show specific epon interface mac address table.
* show mac address-table interface epON 0/1:5 - Using this command to show specific onu interface mac address table.
* show ip sshd - Use this command to show the status.
* show ip traffic - Use this command to show ip traffic information.
* show onu-config-template - Use this command to show template configuration.
* show policy-map - Use this command to show policy map-based bandwidth configuration.
* show telnet - Use this command to show an incoming telnet connection.
* show VLAN - Use this command to show VLAN information.
* show mac-address-table dynamic - Using this command to show dynamic mac address.
Conclusion:
Hope these commands will be useful for beginners.If you don't understand then please comment. I will try to support everyone.